说明：我烧了自己做的影像文件无法启动
0.000000] Console: colour dummy device 80x30
[ 0.000000] console [ttySAC0] enabled
[ 0.434027] Calibrating delay loop... 997.78 BogoMIPS (lpj=2494464)
[ 0.464999] pid_max: default: 32768 minimum: 301
[ 0.465161] Mount-cache hash table entries: 512
[ 0.465492] Initializing cgroup subsys debug
[ 0.465534] Initializing cgroup subsys cpuacct
[ 0.465580] Initializing cgroup subsys freezer
[ 0.467592] CPU: Testing write buffer coherency: ok
[ 0.475180] print_constraints: dummy:
[ 0.476279] NET: Registered protocol family 16
[ 0.485743] S3C Power Management, Copyright 2004 Simtec Electronics
[ 0.492280] fimd at 0x3c331000
[ 0.492361] hsmmc0: sclk_mmc: source is mout_mpll, rate is 47642857
[ 0.496129] hsmmc1: sclk_mmc: source is mout_mpll, rate is 47642857
[ 0.502424] hsmmc2: sclk_mmc: source is mout_mpll, rate is 47642857
[ 0.508591] hsmmc3: sclk_mmc: source is mout_mpll, rate is 47642857
[ 0.515617] S5PV210: Initializing architecture
[ 0.519870] s3c-adc s5pv210-adc: attached adc driver
[ 0.524339] s3c24xx-pwm s3c24xx-pwm.0: tin at 33350000, tdiv at 33350000, tin=divclk, base 0
[ 0.532970] print_constraints: pd_tv_supply: 5000 mV normal
[ 0.538372] print_constraints: pd_lcd_supply: 5000 mV normal
[ 0.544098] print_constraints: pd_g3d_supply: 5000 mV normal
[ 0.549802] print_constraints: pd_mfc_supply: 5000 mV normal
[ 0.555525] print_constraints: pd_audio_supply: 5000 mV normal
[ 0.592384] bio: create slab <bio-0> at 0
[ 0.593349] SCSI subsystem initialized
[ 0.595193] usbcore: registered new interface driver usbfs
[ 0.595486] usbcore: registered new interface driver hub
[ 0.595685] usbcore: registered new device driver usb
[ 0.596231] s3c-i2c s3c2440-i2c.0: slave address 0x10
[ 0.598642] s3c-i2c s3c2440-i2c.0: bus frequency set to 378 KHz
[ 0.605399] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
[ 0.609938] s3c-i2c s3c2440-i2c.1: slave address 0x10
[ 0.614972] s3c-i2c s3c2440-i2c.1: bus frequency set to 65 KHz
[ 0.621014] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
[ 0.626169] s3c-i2c s3c2440-i2c.2: slave address 0x10
[ 0.631157] s3c-i2c s3c2440-i2c.2: bus frequency set to 378 KHz
[ 0.637405] s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter
[ 0.642958] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.649283] Bluetooth: Core ver 2.16
[ 0.652427] NET: Registered protocol family 31
[ 0.656741] Bluetooth: HCI device and connection manager initialized
[ 0.663048] Bluetooth: HCI socket layer initialized
[ 0.667890] Bluetooth: L2CAP socket layer initialized
[ 0.672914] Bluetooth: SCO socket layer initialized
[ 0.678001] Switching to clocksource s5p_clocksource_timer
[ 0.684997] Switched to NOHz mode on CPU #0
[ 0.696993] NET: Registered protocol family 2
[ 0.697182] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.699613] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.706119] TCP bind hash table entries: 16384 (order: 6, 327680 bytes)
[ 0.712728] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.718937] TCP reno registered
[ 0.722041] UDP hash table entries: 256 (order: 1, 12288 bytes)
[ 0.727957] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
[ 0.734479] NET: Registered protocol family 1
[ 0.738842] RPC: Registered named UNIX socket transport module.
[ 0.744534] RPC: Registered udp transport module.
[ 0.749173] RPC: Registered tcp transport module.
[ 0.753852] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.769708] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.769843] PMU: registered new PMU device of type 0
[ 0.772005] cpuidle: phy_regs_save:0x3bf3e000
[ 0.776237] Loaded driver for PL330 DMAC-0 s3c-pl330
[ 0.781013] DBUFF-64x8bytes Num_Chans-8 Num_Peri-2 Num_Events-32
[ 0.787114] Loaded driver for PL330 DMAC-1 s3c-pl330
[ 0.791988] DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 0.798129] Loaded driver for PL330 DMAC-2 s3c-pl330
[ 0.802992] DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 0.817171] ashmem: initialized
[ 0.830964] NTFS driver 2.1.30 [Flags: R/W].
[ 0.831461] ROMFS MTD (C) 2007 Red Hat, Inc.
[ 0.831724] msgmni has been set to 770
[ 0.832698] io scheduler noop registered
[ 0.832736] io scheduler deadline registered
[ 0.832821] io scheduler cfq registered (default)
[ 0.837269] start plist test
[ 0.842940] end plist test
[ 0.843757] s3cfb s3cfb: win 2: pmem_start=0x3c796000
[ 0.847779] s3cfb s3cfb: [fb2] dma: 0x3c796000, cpu: 0xe1000000, size: 0x0085c000
[ 0.866780] Console: switching to colour frame buffer device 100x30
[ 0.871858] FIMD src sclk = 166750000
[ 0.871930] s3cfb s3cfb: registered successfully
[ 0.871971] Start display and show logo
[ 0.878877] s5pv210-uart.0: ttySAC0 at MMIO 0xe2900000 (irq = 16) is a S3C6400/10
[ 0.883522] s5pv210-uart.1: ttySAC1 at MMIO 0xe2900400 (irq = 20) is a S3C6400/10
[ 0.898295] s5pv210-uart.2: ttySAC2 at MMIO 0xe2900800 (irq = 24) is a S3C6400/10
[ 0.908294] s5pv210-uart.3: ttySAC3 at MMIO 0xe2900c00 (irq = 28) is a S3C6400/10
[ 0.918755] leds initialized
[ 0.918918] buttons initialized
[ 0.919101] pwm initialized
[ 0.919294] mini210-adc initialized
[ 0.919582] backlight initialized
[ 0.920413] PA FB = 0x3C796000, bits per pixel = 32
[ 0.923734] screen width=800 height=480 va=0xdc796000 pa=0x3c796000
[ 0.929997] xres_virtual = 800, yres_virtual = 1440, xoffset = 0, yoffset = 0
[ 0.937047] fb_size=8765440
[ 0.939832] Back frameBuffer[0].VAddr=dc90d000 PAddr=3c90d000 size=1536000
[ 0.946668] Back frameBuffer[1].VAddr=dca84000 PAddr=3ca84000 size=1536000
[ 0.953519] Video Y Buffer[0].VAddr=dcbfb000 PAddr=3cbfb000 size=921600
[ 0.960098] Video Y Buffer[1].VAddr=dccdc000 PAddr=3ccdc000 size=921600
[ 0.966682] Video Y Buffer[2].VAddr=dcdbd000 PAddr=3cdbd000 size=921600
[ 0.973268] Video UV Buffer[0].VAddr=dce9e000 PAddr=3ce9e000 size=462848
[ 0.979943] Video UV Buffer[1].VAddr=dcf0f000 PAddr=3cf0f000 size=462848
[ 0.986613] Video UV Buffer[2].VAddr=dcf80000 PAddr=3cf80000 size=462848
[ 0.999653] brd: module loaded
[ 1.002885] loop: module loaded
[ 1.004300] S3C NAND Driver, (c) 2008 Samsung Electronics
[ 1.136030] S3C NAND Driver is using hardware ECC.
[ 1.136106] NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit)
[ 1.136187] Creating 5 MTD partitions on "s5pv210-nand":
[ 1.136238] 0x0000000c0000-0x000000100000 : "misc"
[ 1.138182] 0x000000100000-0x000000600000 : "recovery"
[ 1.144039] 0x000000600000-0x000000b00000 : "kernel"
[ 1.148929] 0x000000b00000-0x000000e00000 : "ramdisk"
[ 1.153637] 0x000000e00000-0x000020000000 : "system"
[ 1.248482] PPP generic driver version 2.4.2
[ 1.248789] PPP Deflate Compression module registered
[ 1.248834] PPP BSD Compression module registered
[ 1.249273] PPP MPPE Compression module registered
[ 1.249317] NET: Registered protocol family 24
[ 1.250742] tun: Universal TUN/TAP device driver, 1.6
[ 1.254466] tun: (C) 1999-2004 Max Krasnyansky <
maxk@qualcomm.com>
[ 1.260788] dm9000 Ethernet Driver, V1.31
[ 1.265742] eth0: dm9000a at e0838000,e083c00c IRQ 39 MAC: 08:90:00:a0:02:10 (platform data)
[ 1.273279] usbcore: registered new interface driver dm9620
[ 1.278629] sdhci: Secure Digital Host Controller Interface driver
[ 1.284663] sdhci: Copyright(c) Pierre Ossman
[ 1.289044] s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133400000 Hz)
[ 1.295580] s3c-sdhci s3c-sdhci.0: clock source 2: sclk_mmc (47642857 Hz)
[ 1.302378] mmc0: no vmmc regulator found
[ 1.306605] mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
[ 1.313401] s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133400000 Hz)
[ 1.319929] s3c-sdhci s3c-sdhci.1: clock source 2: sclk_mmc (47642857 Hz)
[ 1.326708] mmc1: no vmmc regulator found
[ 1.333000] mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
[ 1.337734] s3c-sdhci s3c-sdhci.2: clock source 0: hsmmc (133400000 Hz)
[ 1.344302] s3c-sdhci s3c-sdhci.2: clock source 2: sclk_mmc (47642857 Hz)
[ 1.351080] mmc2: no vmmc regulator found
[ 1.358346] mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA
[ 1.362085] s3c-sdhci s3c-sdhci.3: clock source 0: hsmmc (133400000 Hz)
[ 1.368632] s3c-sdhci s3c-sdhci.3: clock source 2: sclk_mmc (47642857 Hz)
[ 1.375418] mmc3: no vmmc regulator found
[ 1.379652] mmc3: SDHCI controller on samsung-hsmmc [s3c-sdhci.3] using ADMA
[ 1.386528] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.393116] s5p-ehci s5p-ehci: S5P EHCI Host Controller
[ 1.399183] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
[ 1.407196] s5p-ehci s5p-ehci: irq 87, io mem 0xec200000
[ 1.418273] s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
[ 1.418884] hub 1-0:1.0: USB hub found
[ 1.419482] hub 1-0:1.0: 1 port detected
[ 1.423841] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.429681] s5p-ohci s5p-ohci: EXYNOS OHCI Host Controller
[ 1.435057] s5p-ohci s5p-ohci: new USB bus registered, assigned bus number 2
[ 1.442064] s5p-ohci s5p-ohci: irq 87, io mem 0xec300000
[ 1.459804] mmc0: new high speed SD card at address 1234
[ 1.460135] mmcblk0: mmc0:1234 SA02G 1.85 GiB
[ 1.461567] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
[ 1.466196] mmcblk0: retrying using single block read
[ 1.471289] mmcblk0: timed out sending r/w cmd command, card status 0x400b00
[ 1.478234] mmcblk0: command error, retrying timeout
[ 1.484024] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
[ 1.492363] end_request: I/O error, dev mmcblk0, sector 0
[ 1.502599] mmcblk0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
[ 1.507182] hub 2-0:1.0: USB hub found
[ 1.510667] end_request: I/O error, dev mmcblk0, sector 1
[ 1.516040] hub 2-0:1.0: 1 port detected
[ 1.520623] usbcore: registered new interface driver usbserial
[ 1.525779] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
[ 1.535050] USB Serial support registered for generic
[ 1.539958] end_request: I/O error, dev mmcblk0, sector 2
[ 1.545440] usbcore: registered new interface driver usbserial_generic
[ 1.551846] usbserial: USB Serial Driver core
[ 1.556161] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
[ 1.565428] USB Serial support registered for aircable
[ 1.570543] end_request: I/O error, dev mmcblk0, sector 3
[ 1.575853] usbcore: registered new interface driver aircable
[ 1.581666] USB Serial support registered for ark3116
[ 1.586576] mmcblk0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
[ 1.595886] usbcore: registered new interface driver ark3116
[ 1.601395] end_request: I/O error, dev mmcblk0, sector 4
[ 1.606758] ark3116:v0.6:USB ARK3116 serial/IrDA driver
[ 1.612064] USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter
[ 1.620230] mmcblk0: error -84 transferring data, sector 5, nr 3, cmd response 0x900, card status 0x0
[ 1.629519] end_request: I/O error, dev mmcblk0, sector 5
[ 1.634777] usbcore: registered new interface driver belkin
[ 1.640304] belkin_sa: v1.3:USB Belkin Serial converter driver
[ 1.646212] USB Serial support registered for ch341-uart
[ 1.651398] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
[ 1.660727] usbcore: registered new interface driver ch341
[ 1.666042] end_request: I/O error, dev mmcblk0, sector 6
[ 1.671499] USB Serial support registered for cp210x
[ 1.676499] usbcore: registered new interface driver cp210x
[ 1.681903] mmcblk0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
[ 1.691305] cp210x: v0.09:Silicon Labs CP210x RS232 serial adaptor driver
[ 1.697831] end_request: I/O error, dev mmcblk0, sector 7
[ 1.703185] Buffer I/O error on device mmcblk0, logical block 0
[ 1.709259] USB Serial support registered for Reiner SCT Cyberjack USB card reader
[ 1.716811] usbcore: registered new interface driver cyberjack
[ 1.722462] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
[ 1.731644] cyberjack: v1.01 Matthias Bruestle
[ 1.736041] mmcblk0: retrying using single block read
[ 1.741067] cyberjack: REINER SCT cyberJack pinpad/e-com USB Chipcard Reader Driver
[ 1.748710] usb 1-1: new high speed USB device number 2 using s5p-ehci
[ 1.755341] USB Serial support registered for DeLorme Earthmate USB
[ 1.761469] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
[ 1.770763] USB Serial support registered for HID->COM RS232 Adapter
[ 1.776960] end_request: I/O error, dev mmcblk0, sector 0
[ 1.782444] USB Serial support registered for Nokia CA-42 V2 Adapter
[ 1.788661] mmcblk0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
[ 1.797969] usbcore: registered new interface driver cypress
[ 1.803482] end_request: I/O error, dev mmcblk0, sector 1
[ 1.808838] cypress_m8: v1.10:Cypress USB to Serial Driver
[ 1.814411] USB Serial support registered for Digi 2 port USB adapter
[ 1.820727] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
[ 1.830292] USB Serial support registered for Digi 4 port USB adapter
[ 1.836323] end_request: I/O error, dev mmcblk0, sector 2
[ 1.841821] usbcore: registered new interface driver digi_acceleport
[ 1.848021] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
[ 1.857208] digi_acceleport: v1.80.1.2:Digi AccelePort USB-2/USB-4 Serial Converter driver
[ 1.865437] end_request: I/O error, dev mmcblk0, sector 3
[ 1.870914] USB Serial support registered for Edgeport 2 port adapter
[ 1.877220] mmcblk0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
[ 1.886530] USB Serial support registered for Edgeport 4 port adapter
[ 1.892844] end_request: I/O error, dev mmcblk0, sector 4
[ 1.898319] USB Serial support registered for Edgeport 8 port adapter
[ 1.904721] USB Serial support registered for EPiC device
[ 1.910221] usbcore: registered new interface driver io_edgeport
[ 1.915976] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
[ 1.925440] io_edgeport: v2.7:Edgeport USB Serial Driver
[ 1.930569] end_request: I/O error, dev mmcblk0, sector 6
[ 1.935841] hub 1-1:1.0: USB hub found
[ 1.939674] USB Serial support registered for Edgeport TI 1 port adapter
[ 1.946192] hub 1-1:1.0: 4 ports detected
[ 1.950333] USB Serial support registered for Edgeport TI 2 port adapter
[ 1.956942] mmcblk0: error -84 transferring data, sector 7, nr 1, cmd response 0x900, card status 0x0
[ 1.966250] usbcore: registered new interface driver io_ti
[ 1.971530] end_request: I/O error, dev mmcblk0, sector 7
[ 1.976846] Buffer I/O error on device mmcblk0, logical block 0
[ 1.982857] io_ti: v0.7mode043006:Edgeport USB Serial Driver
[ 1.988520] USB Serial support registered for empeg
[ 1.993654] usbcore: registered new interface driver empeg
[ 1.998730] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
[ 2.007913] empeg: v1.3:USB Empeg Mark I/II Driver
[ 2.012652] mmcblk0: retrying using single block read
[ 2.017778] USB Serial support registered for FTDI USB Serial Device
[ 2.024252] usbcore: registered new interface driver ftdi_sio
[ 2.029744] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0
[ 2.038925] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
[ 2.044716] end_request: I/O error, dev mmcblk0, sector 0
[ 2.050187] USB Serial support registered for funsoft
[ 2.055262] usbcore: registered new interface driver funsoft
[ 2.060763] mmcblk0: error -84 transferring data, sector 1, nr 7, cmd response 0x900, card status 0x0
[ 2.070069] USB Serial support registered for Garmin GPS usb/tty
[ 2.075927] end_request: I/O error, dev mmcblk0, sector 1
[ 2.081423] usbcore: registered new interface driver garmin_gps
[ 2.087211] garmin_gps: v0.36:garmin gps driver
[ 2.091721] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd response 0x900, card status 0x0
[ 2.101002] USB Serial support registered for hp4X
[ 2.105763] end_request: I/O error, dev mmcblk0, sector 2
[ 2.111070] usbcore: registered new interface driver hp4X
[ 2.116426] hp4x: v1.00:HP4x (48/49) Generic Serial driver
[ 2.122006] USB Serial support registered for PocketPC PDA
[ 2.127317] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd response 0x900, card status 0x0
[ 2.136706] usbcore: registered new interface driver ipaq
[ 2.141874] end_request: I/O error, dev mmcblk0, sector 3
[ 2.147233] ipaq: v1.0:USB PocketPC PDA driver
[ 2.151767] USB Serial support registered for IPWireless converter
[ 2.157817] mmcblk0: error -84 transferring data, sector 4, nr 4, cmd response 0x900, card status 0x0
[ 2.167122] usbcore: registered new interface driver ipwtty
[ 2.172548] end_request: I/O error, dev mmcblk0, sector 4
[ 2.177908] ipw: v0.4:IPWireless tty driver
[ 2.182179] USB Serial support registered for IR Dongle
[ 2.187432] usbcore: registered new interface driver ir-usb
[ 2.192826] mmcblk0: error -84 transferring data, sector 6, nr 2, cmd response 0x900, card status 0x0
[ 2.202016] ir_usb: v0.5:USB IR Dongle driver
[ 2.206328] end_request: I/O error, dev mmcblk0, sector 6
[ 2.211800] USB Serial support registered for iuu_phoenix
[ 2.217226] usbcore: registered new interface driver iuu_phoenix
[ 2.223104] Buffer I/O error on device mmcblk0, logical block 0
[ 2.228973] mmcblk0: unable to read partition table
[ 2.234312] iuu_phoenix: v0.12:Infinity USB Unlimited Phoenix driver
[ 2.240329] USB Serial support registered for Keyspan PDA
[ 2.245729] USB Serial support registered for Keyspan PDA - (prerenumeration)
[ 2.254890] USB Serial support registered for Xircom / Entregra PGS - (prerenumeration)
[ 2.260802] usbcore: registered new interface driver keyspan_pda
[ 2.266685] keyspan_pda: v1.1:USB Keyspan PDA Converter driver
[ 2.275718] USB Serial support registered for KL5KUSB105D / PalmConnect
[ 2.279176] usbcore: registered new interface driver kl5kusb105d
[ 2.285029] kl5kusb105: v0.4:KLSI KL5KUSB105 chipset USB->Serial Converter driver
[ 2.294595] USB Serial support registered for KOBIL USB smart card terminal
[ 2.299540] usbcore: registered new interface driver kobil
[ 2.304873] kobil_sct: 21/05/2004:KOBIL USB Smart Card Terminal Driver (experimental)
[ 2.313805] usb 1-1.1: new high speed USB device number 3 using s5p-ehci
[ 2.321523] USB Serial support registered for MCT U232
[ 2.324639] usbcore: registered new interface driver mct_u232
[ 2.330202] mct_u232: z2.1:Magic Control Technology USB-RS232 converter driver
[ 2.339499] USB Serial support registered for Moschip 2 port adapter
[ 2.343714] mos7720: 2.1:Moschip USB Serial Driver
[ 2.348610] usbcore: registered new interface driver moschip7720
[ 2.357653] USB Serial support registered for Moschip 7840/7820 USB Serial Driver
[ 2.361922] mos7840: 1.3.2:Moschip 7840/7820 USB Serial Driver
[ 2.367806] usbcore: registered new interface driver mos7840
[ 2.375440] USB Serial support registered for moto-modem
[ 2.378743] usbcore: registered new interface driver moto-modem
[ 2.384620] USB Serial support registered for navman
[ 2.392697] usbcore: registered new interface driver navman
[ 2.395102] USB Serial support registered for ZyXEL - omni.net lcd plus usb
[ 2.402054] usbcore: registered new interface driver omninet
[ 2.409692] omninet: v1.1:USB ZyXEL omni.net LCD PLUS Driver
[ 2.413317] USB Serial support registered for opticon
[ 2.418376] usbcore: registered new interface driver opticon
[ 2.423956] USB Serial support registered for GSM modem (1-port)
[ 2.430067] usbcore: registered new interface driver option
[ 2.436476] option: v0.7.2:USB Driver for GSM modems
[ 2.442549] USB Serial support registered for oti6858
[ 2.445978] usbcore: registered new interface driver oti6858
[ 2.451042] hub 1-1.1:1.0: USB hub found
[ 2.455055] hub 1-1.1:1.0: 4 ports detected
[ 2.459053] USB Serial support registered for pl2303
[ 2.464211] usbcore: registered new interface driver pl2303
[ 2.469589] pl2303: Prolific PL2303 USB to serial adaptor driver
[ 2.475642] USB Serial support registered for qcaux
[ 2.480732] usbcore: registered new interface driver qcaux
[ 2.486100] USB Serial support registered for Qualcomm USB modem
[ 2.491970] usbcore: registered new interface driver qcserial
[ 2.499569] safe_serial: v0.1:USB Safe Encapsulated Serial
[ 2.503038] USB Serial support registered for safe_serial
[ 2.508520] usbcore: registered new interface driver safe_serial
[ 2.514437] USB Serial support registered for siemens_mpi
[ 2.519856] usbcore: registered new interface driver siemens_mpi
[ 2.526694] Driver for Siemens USB/MPI adapter
[ 2.532093] Version 0.1 09/26/2005 Thomas
Hergenhahn@web.de http://libnodave.sf.net[ 2.537821] USB Serial support registered for Sierra USB modem
[ 2.543682] usbcore: registered new interface driver sierra
[ 2.549090] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
[ 2.555669] USB Serial support registered for SPCP8x5
[ 2.560736] usbcore: registered new interface driver spcp8x5
[ 2.566262] spcp8x5: v0.10:SPCP8x5 USB to serial adaptor driver
[ 2.572196] usb 1-1.2: new high speed USB device number 4 using s5p-ehci
[ 2.578963] USB Serial support registered for Quatech SSU-100 USB to Serial Driver
[ 2.586597] usbcore: registered new interface driver ssu100
[ 2.591951] ssu100: v0.1:Quatech SSU-100 USB to Serial Driver
[ 2.597741] USB Serial support registered for symbol
[ 2.602671] usbcore: registered new interface driver symbol
[ 2.608216] USB Serial support registered for TI USB 3410 1 port adapter
[ 2.616930] USB Serial support registered for TI USB 5052 2 port adapter
[ 2.621562] usbcore: registered new interface driver ti_usb_3410_5052
[ 2.627862] ti_usb_3410_5052: v0.10:TI USB 3410/5052 Serial Driver
[ 2.634098] USB Serial support registered for Handspring Visor / Palm OS
[ 2.640788] USB Serial support registered for Sony Clie 3.5
[ 2.647330] USB Serial support registered for Sony Clie 5.0
[ 2.653921] usbcore: registered new interface driver visor
[ 2.657223] visor: USB HandSpring Visor / Palm OS driver
[ 2.662615] USB Serial support registered for Connect Tech - WhiteHEAT - (prerenumeration)
[ 2.670892] USB Serial support registered for Connect Tech - WhiteHEAT
[ 2.677477] usbcore: registered new interface driver whiteheat
[ 2.683076] whiteheat: v2.0:USB ConnectTech WhiteHEAT driver
[ 2.688802] USB Serial support registered for vivopay-serial
[ 2.694490] usbcore: registered new interface driver vivopay-serial
[ 2.700614] vivopay_serial: v1.0:ViVOpay USB Serial Driver
[ 2.706146] USB Serial support registered for zio
[ 2.710862] usbcore: registered new interface driver zio
[ 2.716019] Initializing USB Mass Storage driver...
[ 2.721072] usbcore: registered new interface driver usb-storage
[ 2.729169] USB Mass Storage support registered.
[ 2.732248] s3c-udc : S3C HS USB Device Controller Driver, (c) 2008-2009 Samsung Electronics
[ 2.732254] s3c-udc : version 15 March 2009 (DMA Mode)
[ 2.750650] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 2.751753] android_usb gadget: Number of LUNs=1
[ 2.756425] lun0: LUN: removable file: (no medium)
[ 2.761586] android_usb gadget: android_usb ready
[ 2.786377] Registered gadget driver 'android_usb'
[ 2.786701] mousedev: PS/2 mouse device common for all mice
[ 2.787201] touchscreen-1wire initialized
[ 2.787237] backlight-1wire initialized
[ 2.787322] setup_irq: ret = 0
[ 2.787355] PWM clock = 66700000
[ 2.790247] TCNT_FOR_SAMPLE_BIT = 3472, TCFG1 = 00000003
[ 2.795870] input: fa_ts_input as /devices/virtual/input/input0
[ 2.801910] ts-if initialized
[ 2.807799] input: ft5x0x_ts as /devices/virtual/input/input1
[ 2.813482] usb 1-1.1.1: new high speed USB device number 5 using s5p-ehci
[ 2.818448] ft5x0x_ts 2-0038: Firmware version 0x12
[ 2.821751] ft5x0x_ts 2-0038: FocalTech ft5x0x 7 TouchScreen initialized
[ 2.830883] S3C24XX RTC, (c) 2004,2006 Simtec Electronics
[ 2.833903] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[ 2.839325] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[ 2.844771] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[ 2.850222] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[ 2.856701] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[ 2.863571] using rtc device, s3c, for alarms
[ 2.865299] s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
[ 2.871676] i2c /dev entries driver
[ 2.875658] Linux video capture interface: v2.00
[ 2.879705] mfc_init: <6>S5PC110 MFC Driver, (c) 2009 Samsung Electronics
[ 2.879711]
[ 2.890871] S3C JPEG Driver, (c) 2007 Samsung Electronics
[ 2.893150] JPEG driver for S5PV210
[ 2.897277] i2c i2c-1: attached s5p_ddc into i2c adapter successfully
[ 2.903192] S5PC11X HPD Driver, (c) 2010 Samsung Electronics
[ 2.911162] S5PC11X CEC Driver, (c) 2010 Samsung Electronics
[ 2.915268] usbcore: registered new interface driver uvcvideo
[ 2.920126] USB Video Class driver (v1.1.0)
[ 2.939802] uvcvideo: Found UVC 1.00 device Vimicro USB 2.0 PC Camera (Venus) (0ac8:3420)
[ 2.948604] input: Vimicro USB 2.0 PC Camera (Venu as /devices/platform/s5p-ehci/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.0/input/input2
[ 2.979084] input: mma7660 as /devices/platform/s3c2440-i2c.0/i2c-0/0-004c/input/input3
[ 2.979353] mma7660 0-004c: MMA7660 device is probed successfully.
[ 2.979517] i2c-core: driver [mma7660] using legacy suspend method
[ 2.979592] i2c-core: driver [mma7660] using legacy resume method
[ 2.983196] MMA7660 sensor driver registered.
[ 2.987559] S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
[ 2.993720] s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
[ 3.002054] device-mapper: uevent: version 1.0.3
[ 3.006115] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised:
dm-devel@redhat.com[ 3.014139] Bluetooth: HCI UART driver ver 2.2
[ 3.018498] Bluetooth: HCI H4 protocol initialized
[ 3.023309] usb 1-1.1.2: new high speed USB device number 6 using s5p-ehci
[ 3.030089] Bluetooth: HCILL protocol initialized
[ 3.034913] cpuidle: using governor ladder
[ 3.039107] cpuidle: using governor menu
[ 3.043267] 4: TCNTB=00000d90, TCNTO=00000545, TINT_CSTAT=0000000c
[ 3.055323] usbcore: registered new interface driver usbhid
[ 3.055375] usbhid: USB HID core driver
[ 3.059711] ALSA device list:
[ 3.061160] No soundcards found.
[ 3.064617] oprofile: hardware counters not available
[ 3.069648] oprofile: using timer interrupt.
[ 3.073931] GACT probability NOT on
[ 3.077289] Mirror/redirect action on
[ 3.080942] u32 classifier
[ 3.083615] Actions configured
[ 3.086986] Netfilter messages via NETLINK v0.30.
[ 3.091733] nf_conntrack version 0.5.0 (6165 buckets, 24660 max)
[ 3.098534] ctnetlink v0.93: registering with nfnetlink.
[ 3.102976] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 3.109942] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 3.116183] xt_time: kernel timezone is -0000
[ 3.121587] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.125500] arp_tables: (C) 2002 David S. Miller
[ 3.129961] TCP cubic registered
[ 3.134108] NET: Registered protocol family 10
[ 3.142237] Mobile IPv6
[ 3.142288] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 3.145644] IPv6 over IPv4 tunneling driver
[ 3.153990] NET: Registered protocol family 17
[ 3.154058] NET: Registered protocol family 15
[ 3.158489] Bluetooth: RFCOMM TTY layer initialized
[ 3.163239] Bluetooth: RFCOMM socket layer initialized
[ 3.168332] Bluetooth: RFCOMM ver 1.11
[ 3.172270] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 3.177416] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.183562] NET: Registered protocol family 35
[ 3.188052] uvcvideo: Found UVC 1.00 device Vimicro USB 2.0 PC Camera (Venus) (0ac8:3420)
[ 3.195971] Registering the dns_resolver key type
[ 3.200606] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
[ 3.208095] ThumbEE CPU extension supported.
[ 3.212535] s5pv210_cpufreq_init: S5PV210 cpu-freq driver
[ 3.218224] input: Vimicro USB 2.0 PC Camera (Venu as /devices/platform/s5p-ehci/usb1/1-1/1-1.1/1-1.1.2/1-1.1.2:1.0/input/input4
[ 3.229812] regulator_init_complete: pd_mfc_supply: disabling
[ 3.234974] regulator_init_complete: pd_tv_supply: disabling
[ 3.241203] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[ 3.246020] 4: TCNTB=00000d90, TCNTO=000006c1, TINT_CSTAT=0000000c
[ 3.253041] s3c-rtc s3c64xx-rtc: setting system clock to 2012-01-01 12:00:00 UTC (1325419200)
[ 3.262150] FIMC0 registered successfully
[ 3.265963] FIMC1 registered successfully
[ 3.269931] FIMC2 registered successfully
[ 3.272720] S5PC1XX TVOUT Driver, (c) 2009 Samsung Electronics
[ 3.279008] s5p-tvout s5p-tvout: hpd status is cable removed
[ 3.290561] Freeing init memory: 1456K
[ 3.297988] yaffs: dev is 32505860 name is "mtdblock4" rw
[ 3.298038] yaffs: passed flags ""
1Wire touchscreen OK
/init: line 109: can't open /r/dev/console: no such file
[ 3.583353] Kernel panic - not syncing: Attempted to kill init!
[ 3.583438] [<c0184fe4>] (unwind_backtrace+0x0/0xf0) from [<c06860c8>] (panic+0x70/0x1ac)
[ 3.583518] [<c06860c8>] (panic+0x70/0x1ac) from [<c01a1520>] (do_exit+0x5dc/0x68c)
[ 3.583591] [<c01a1520>] (do_exit+0x5dc/0x68c) from [<c01a182c>] (do_group_exit+0x3c/0xbc)
[ 3.591018] [<c01a182c>] (do_group_exit+0x3c/0xbc) from [<c01a18bc>] (sys_exit_group+0x10/0x18)
[ 3.599682] [<c01a18bc>] (sys_exit_group+0x10/0x18) from [<c017f640>] (ret_fast_syscall+0x0/0x30)
[ 3.608516] Rebooting in 5 seconds..
[ 8.616153] Restarting Linux version 3.0.8-FriendlyARM (Booting from SD
