你好，我使用Tiny2416核心板，液晶屏用的是群创的4.3寸480*272的AT043TN25，烧入的是wince6.0，发现系统不能正常启动， 上电后com0发出的状态如下，请帮我解决一下这个问题呗，谢谢。
Superboot-2451 V1.08a(20150708) by FriendlyARM
Booting from NAND
Launch Windows CE...
Windows CE Kernel for ARM (Thumb Enabled) Built on Nov 3 2010 at 07:30:04
INFO:OALLogSetZones: dpCurSettings.ulZoneMask: 0xb
DCache: 128 sets, 4 ways, 32 line size, 16384 size
ICache: 128 sets, 4 ways, 32 line size, 16384 size
FCLK:400000000, HCLK:133333333, PCLK:66666666
+OALArgsInit()
Arguments area is initialized
-OALArgsInit()
TCNTB4: 8234 8234
TCFG0 : 0
TCFG1 : 0
-OEMInit
[OAL]++OEMEnumExtensionDRAM
cMemSections = 15
[OAL] --OEMEnumExtensionDRAM
#### FMD_DRIVER:::FMD_INIT
(NAND ID:0xecda) --> OK.
NUM_OF_BLOCKS = 2048
PAGES_PER_BLOCK = 64
SECTORS_PER_PAGE = 4
FMD_OEMIoControl: IOCTL_FMD_GET_INTERFACE
NUMBLOCKS : 1773(0x6ed), SECTORSPERBLOCK = 64(0x40), BYTESPERSECTOR = 2048(0x800)
NUMBLOCKS : 1773(0x6ed), SECTORSPERBLOCK = 64(0x40), BYTESPERSECTOR = 2048(0x800)
NUMBLOCKS : 1773(0x6ed), SECTORSPERBLOCK = 64(0x40), BYTESPERSECTOR = 2048(0x800)
FMD_OEMIoControl: unrecognized IOCTL (0x71c24).
NUMBLOCKS : 1773(0x6ed), SECTORSPERBLOCK = 64(0x40), BYTESPERSECTOR = 2048(0x800)
OEM: Not cleaning system hive
OEM: Not cleaning user profiles
OEM: Not cleaning system hive
DEBUG: CreateSerialObject 0
DEBUG: CreateSerialObject 1
DEBUG: CreateSerialObject 2
DEBUG: CreateSerialObject 3
Audio Input IRQ(DMA1) mapping: [IRQ:41->sysIRQ:22].
Audio Output IRQ(DMA2) mapping: [IRQ:42->sysIRQ:23].
I2CWrite ERROR: 1460
I2CWrite ERROR: 1460
I2CWrite ERROR: 1460
I2CWrite ERROR: 1460
I2CWrite ERROR: 1460
I2CWrite ERROR: 1460
I2CWrite ERROR: 1460
I2CWrite ERROR: 1460
I2CWrite ERROR: 1460
I2CWrite ERROR: 1460
I2CWrite ERROR: 1460
I2CWrite ERROR: 1460
I2CWrite ERROR: 1460
I2CWrite ERROR: 1460
I2CWrite ERROR: 1460
I2CWrite ERROR: 1460
I2CWrite ERROR: 1460
I2CWrite ERROR: 1460
I2CWrite ERROR: 1460
I2CWrite ERROR: 1460
+OALIoCtlHalGetHWEntropy
HOST CAP : 4
[DISP:INF] g_pLcdConReg = 0xd29e0000
[DISP:INF] g_pGPIOReg = 0xd2a00000
DM9K BANK Init.
[dm9: Chip signature is 2B2A2928
[HSMMC1] Initializing the HSMMC Host Controller
[HSMMC1] Turn OFF the F/B delay control.
[HSMMC0] Initializing the HSMMC Host Controller
[HSMMC0] Turn OFF the F/B delay control.
[HSMMC0] Card is Removed!
[HSMMC1] Card is Removed!
USB Serial Function Class Enabled : Serial_Class
+OALIoCtlHalGetDeviceInfo(...)
OALIoCtlHalGetDeviceInfo():SPI_GETUUID
-OALIoCtlHalGetDeviceInfo(SPI = SPI_GETUUID, rc = 1)
LED_Init
LED_Gpio_Setting
++OALIoCtlHalGetDispInfo()
Exception 'Data Abort' (4): Thread-Id=04070002(pth=828896e4), Proc-Id=00400002(pprc=820b8308) 'NK.EXE', VM-active=016c0006(pprc=8361221c) 'udevice.exe'
PC=8020a050(NK.EXE+0x0000a050) RA=8020ba90(NK.EXE+0x0000ba90) SP=d31af53c, BVA=00000000
[OAL:ERR] OALIoCtlHalGetDispInfo() Failed dwErr = 0x00000057
--OALIoCtlHalGetDispInfo()
++OALIoCtlHalGetDispInfo()
Exception 'Data Abort' (4): Thread-Id=04070002(pth=828896e4), Proc-Id=00400002(pprc=820b8308) 'NK.EXE', VM-active=016c0006(pprc=8361221c) 'udevice.exe'
PC=8020a050(NK.EXE+0x0000a050) RA=8020ba90(NK.EXE+0x0000ba90) SP=d31af420, BVA=00000000
[OAL:ERR] OALIoCtlHalGetDispInfo() Failed dwErr = 0x00000057
--OALIoCtlHalGetDispInfo()
FriendlyARM got the LCD paramters, Name is
[DISP:INF] VCLK Source = LCDCLK from EPLL (96000000 Hz)
[DISP:INF] VCLKSrc = 96000000, VCLK = 220567720, Div = 0
[DISP:ERR] --Disp_get_vclk_direction_divider() : VCLK Source is Too Slow
[DISP:ERR] Disp_initialize_RGBIF() : Clock Source Decision Failed
LDI_LTE480WV_RGB_port_initialize(): dont know why set GPB1
